DESCRIPTION: ULTRA-PLUG is a quick setting, hydraulic, cementious, water stopping grout which provides a tight bonding, dense barrier to permanently seal out active water. When mixed with clean water, this formula sets in 3 to 5 minutes at 70ºF (21ºC).

• For use in foundation and retaining walls, dams, tunnels, sewers, waste water treatment plants, mines, wells, elevator pits, cisterns and tanks
• To plug any leaks in any concrete or masonry surface
• To prevent seepage along cracks or seams at the floor and wall intersection and seal holes left by tie wires
• To seal all leaks around piping and conduit passing through concrete and masonry walls

• Fast setting
• Stops flowing water
• Very low shrinkage
• Easy to handle
• Sets up under water
• Excellent freeze/thaw resistance
• Nonmetallic
• High early strength
• U.S.D.A. approved

PACKAGING: ULTRA-PLUG is packaged in a 50 lb. pail or a 10 lb. can.

YIELD: ULTRA-PLUG will yield approximately 0.4 cu. ft. (0.01 cu. m.) per 50 lbs.

STORAGE CONDITIONS: Store ULTRA-PLUG at or above 45ºF (7ºC) in a dry area. Avoid excessive heat or humidity. Shelf life is one year in the original, unopened container.

POT LIFE: ULTRA-PLUG has a pot life of 2 minutes at 70ºF (21ºC). Cold water 40ºF (4ºC) will retard the set time and hot water 90ºF (32ºC) will accelerate the set time.

CURING: The curing time of ULTRA-PLUG is approximately 3 to 5 minutes at 70ºF (21ºC).

SURFACE PREPARATION: Undercut the substrate and open the crack or hole to a minimum depth and width of 1 inch (2.5 cm). Wire brush and then flush away all loose material. Remove all oil, grease, dirt and other contaminates to expose clean sound concrete. All traces of oil, dirt or grease must be removed by scrubbing with an industrial detergent. After scrubbing, flush thoroughly with clean water. The substrate surface must be thoroughly wet before applying ULTRA-PLUG.

COLOR: ULTRA-PLUG is available in gray only.

PRIMING: The use of a primer before the application of ULTRA-PLUG is not necessary.

PRODUCT MIXING: ULTRA-PLUG is supplied as a pre-measured unit. Using a small amount of water, mix the material in a small pail until a putty type consistency is obtained. Do not mix more material than can be placed in 2 minutes.

APPLICATION: To stop flowing water ULTRA-PLUG must be placed immediately after mixing. Using gloved hands, form the material into a cone shape and hold until a slight rise in temperature occurs. Then firmly press and hold the ULTRA-PLUG into the repair area until final set occurs. The ULTRA-PLUG may now be shaved to obtain a flush finish with the surface. In other areas of repair ULTRA-PLUG may be troweled into open cracks and joints.

COVERAGE: 1-lb. will fill 17 cu. in., or a crack 3/4 x 3/4 x 30 inches.

• Apply onto a clean, sound, properly prepared substrate
• Application and curing times are depended upon ambient conditions. Cold temperatures retard set time and hot temperatures accelerate set time
• Minimum ambient surface temperature should be above 50ºF (10ºC) at the time of application, however, warm water should be used to mix the materials at lower temperatures. Call BVS technical services for more information on cold weather applications
• Inactive leaks should be thoroughly damped before and for approximately 15 minutes following application

• Dispose of waste materials in accordance with Federal, State and local regulations
• The use of a dust mask, safety. goggles and rubber gloves is recommended
• CAUTION - contains Portland Cement which is highly caustic
• Contains Free Silica. Do not breath the dust as inhalation may cause delayed lung injury (silicosis) and is a carcinogen
• In case of contact, flush eyes with water. Wash skin with soap and water. Contact a Physician
• Use only with adequate ventilation
• Keep out of the reach of children